421 or 427 sbc rotating assembly in a 400 gm passenger block
 

will it work and wat style main caps will work

With both the 3.875" and 4.00" stroke cranks you'll need to clearance the block. Additionally, you'll need a .900" small base-circle cam and have to check the clearance with the rods and cam lobes.

Both cranks are built to work with the 400 main bearing diameters.

Also, the GM 400 blocks will not hold-up as-well-as Dart 400 blocks.

WD

I dare you to go to the CHEVELLE forum and tell those guys the factory 400 block sucks....

That sounds like a challenge.LOL

They blasted me for it.... :lol: for about 4 pages, but that's only because I kept responding.

They sound like hardcore guys

That isnt being hardcore, thats just showing there ignorance to a obvious problem! I have seen three here in my circle of friends split in bracket motors. No power adders at all, single carb bracket engines. They split about a inch down from the top of the cylinder. I think they would be fine in a street engine but .060 over is a no-no in any combo.

[quote="supergass"]That isnt being hardcore, thats just showing there ignorance to a obvious problem!

Agree, stubborn ignorance & wanting to stay that way obviously.

Actually it was only a page or two not 4 ...here is the quote that upset two or three people.One of them called it "rude"

See I really dont see anything wrong with what you said. You said everything based on facts not opinion. So they should have respected that and possibly let it go or just reply to it with their facts. JMO

400 blks. are o'k if they are your only options, i've got 2 of them and have had 1/2 doz. in the past. If they are prepared correctly they will handle 600hp for a time. The bottom end and cylinder walls being the weakest points. I personally drill out the steam hole and put pipe plugs in them (keeps them from cracking to the bolt holes)also fill the block to the bottom of the water pump bolts. I've cracked cylinders, broke main webs but have never blown one to pieces. I've had friends that blew the cranks out the bottom and split the steam holes to the bolt holes. This has never happened too me. The best thing about a 400 blk. is that they are getting harder and harder to find, most have gone by the wayside due to racing mishaps.
bottom line is the Dart block is Sooo much better and safer build. I got one of those too.
The 377" in my malibu is a stock block and welded, but i would not recommend doing what i did to keep it alive.

JMO

Zip.

Not this time
 

I know even after i had Howard's splayed caps installed in my 400 i still chickened out using it in a supercharged application. Where do i find these guy's that love these 400 blocks, i'll sell mine .030 over Howard's splayed caps plate hone 750.00. Never assy. after machine work.

Re: Not this time
 

TEAM CHEVELLE FORUM.

Tod74: Thanks if i get rid of it i'll use the money towards a new Dart tall deck to build a 434 with a Vortec ysi supercharger. Can't wait to get started.

Just another note on the GM400. I have some strange friends that drive in left hand circles. When they build a 400, they use the 2 bolt bottom end because the outer (straight pattern) bolt holes weakens the webbing.

Dave

yep.

Ok you guys can call me slow.. But, I just realized that I have a SB 400 in my 4x4 that was just built. It was beefed up some but I dont know how much. So yeah it has power. Anyways, should I worry bout this motor trashing itself or no?

DirkaDirka: I think what they are saying is when you start applying big power something over say 5oo-550 hp i wound'nt look at it as being a long term reliable piece.

I think your ok Dirka, its only in high compression race engines have I seen the problem. Despite the weaknessess of the 400 block it is my favorite engine all around because it is so amazing. I built a 406 with ported Brodix heads and GM Block with a solid lift cam and 10.5 to 1 compression. In a 3200lbs car with a glide and 5000 stall converter it ran 10.60s with a best (in good air) of a 10:55. It ran for 3 seasons every weekend and no problems. Took it out and change compression to 14.5 to 1 and a roller cam, split the cylinder in the 1st pass!!!! Awesome engine tho.

Chris

Ok I was just wondering cuz I didnt want to be out at the sand dunes with it and the motor crap out on me.

I'm going with a Dart Little-M Sportsman 400 block on my new build. I had considered the Dart 400 SHP, but decided to play-it-safe with the Little-M.

WD

I ripped the deck off my 400 block, it never totally came off, but it cracked the top of the cylinders. I was pushing 15-1 though!!! :oops: I was just curious how much she would take, I think I found it!!! :twisted: Next stop....TALL DECK DART!!!